AUDI J518 ELV Emulator Audi J518 Access Start Control Module For AUDI C6 Q7 A6 Steering Column Module Repair Replacement with VVDI Prog Dedicated Programming Cable

AUDI J518 ELV Emulator without a lock or lock function is three kinds of MCUs that can Repair this emulator. Audi J518 Access Start Control Module For AUDI C6 Q7 A6 Steering Column Module Repair Replacement with VVDI Prog Dedicated Programming Cable. CheShiTech.com AUDI C6 Q7 A6 Steering Module Repair J518 ELV Emulator Audi A6 Q7 C6 steering column lock J518 ELV module failure replacement emulator Fit for R270 CGDI CG100 CG100X XHORSE VVDI Prog.

AUDI J518 ELV Emulator Audi J518 Access Start Control Module For AUDI C6 Q7 A6 Steering Column Module Repair Replacement with VVDI Prog Dedicated Programming Cable

CheShiTech.com AUDI C6 Q7 A6 Steering Module Repair J518 ELV Emulator Audi A6 Q7 C6 steering column lock J518 ELV module failure replacement emulator Fit for R270 CGDI CG100 CG100X XHORSE VVDI Prog

AUDI J518 ELV Emulator Introduction:

Applied to repair the AUDI sixth Gen A6 Q7 Audi C6 steering column lock J518 ELV module failure replacement emulator.

Highlight for Audi Steering Module J518 ELV Emulator:

1. Can be used with R270, CGDI CG100 ,CGDI CG100X, XHORSE VVDI Prog Programmer
2. Universal solution, three types of MCU all can be replaced by this emulator, (replace MCU Mask: 1L59W, 3L40K, 0L01Y directly);
3. Stable and durable, with No Vulnerable components such as relays, micro switches, and motors on it.
4. Easy for replacing, write in the dump form the original J518 Module with the VVDI PROG dedicated line directly, No need for solder wire.

Note:

The Emulator is without a lock or lock function, if you need the same function as the original J518 emulator module, please buy a J518 repair.
The dedicated VVDI PROG programming cable connector here is only for emulator board programming, not for the original J518 PCB.
If you have a car that needs to repair the J518 module with this emulator, you need to read the data in the MCU by wire soldering or other ways.
Then write data into the emulator MCU via this dedicated cable connector.

Applied to repair the AUDI sixth Gen A6 Q7 Audi C6 steering column lock J518 ELV module failure replacement emulator.

AUDI Q7 A6 C6 Steer column module Operating Instructions：

J518 256,128 simulate board instruction

As for reading and programming the original car,pls check the VVDI prog.

If your car is 9S12DG 128 CPU, the operation steps are as follows.

1. Read out the EEPROM data, atttention! Pls save the data, in case of any wrong operation.

2. Put the EEPROM data into the folder”EPROM 2K-4K”, then double-click the EEPROM Converter application, and see that the original 2K file becomes 4K, the conversion is successful.

3. After runing the sytem, the file to be 4K, then the programming succeed

Note: You can only double click one time, do not repeat. If the double-click run is unsuccessful, or no 4K file appears, then right-key to run the program in administrator mode.

Connect flashing wire and write the converted EEPROM file. Attention: simulator is a 256 chip then choose J518 (2010) (0L01Y) required.

Each board is with ep data and FLSAH data, so usually you just need to write EP data.If not, you can write the EP data from your car with the FLASH data in the instruction.

If car is 9S12DG 256 CPU, the operation steps are as follows.

1. Read out and save the original car data, and write it directly to the simulator.

VVDI burning line: where: red (thick) =VCC black (thick) =GND yellow =RST purple =BKGD green =XCLKS White =CLK black (fine) =GND-C

without horn

With horn: wiring according to the silk print in the board ,same as board wihtout horn

Buy our special burning line, with speakers you can avoid welding burning, directly connect the 20pin port.
Attention:
The simulator is burned after the test, preferably on the car.
In the platform test, it is necessary to check the wiring of 20Pin port. Some of the platform wiring harness have production problems and are compatible with our burning interface, which may lead to chip damage.
Error wiring: 10 (red) should recover after 20 (blue) or as shown in the figure.

How to use AUDI Q7 A6 C6 Steer column module:

1. Read out the EEPROM data from the original J518 module of your car (the emulator was already with flash data)
2. Write the EEPROM data you got in Step 1 into the emulator (if the original J518 MCU mask is 0L01Y, write the EEPROM data you got from step1 into the emulator directly;
or if the MCU mask of the original J518 is 1L59W/3L40K, you need to send EEPROM data to an expert to transfer EEPROM data when you write into the emulator directly. We don’t provide the service)

AUDI Q7 A6 C6 Steer column module Package Includes:

1pc x AUDI Q7 A6 C6 Steer column module J518 ELV Module Emulator with VVDI Dedicated programming cable