12V Car Battery Parasitic Drain Tester with Car Blade Fuses Kit Car Automotive Power Drain Leakage Tester Cable Tool w/U-shaped Battery Clamp for Current Automotive Battery Testing

描述

12V Car Battery Parasitic Drain Tester with Car Blade Fuses Kit Replaceable in-line fuses protect both the meter and tester in the event a high current source on the vehicle is left on. Car Automotive Power Drain Leakage Tester Cable Tool w/U-shaped Battery Clamp for Current Automotive Battery Testing. CheShiTech.com 12V Automotive Parasitic drain Tester Car Battery Drain Tester Parasitic Current Detector with Replaceable Fuse.

12V Car Battery Parasitic Drain Tester with Car Blade Fuses Kit Car Automotive Power Drain Leakage Tester Cable Tool w/U-shaped Battery Clamp for Current Automotive Battery Testing

CheShiTech.com 12V Automotive Parasitic drain Tester Car Battery Drain Tester Parasitic Current Detector with Replaceable Fuse

Provides an easy method to connect a multimeter to the vehicle electrical system to diagnose drain.

12V Car Battery Parasitic Drain Tester with Car Blade Fuses Kit Features:

Replaceable in-line fuses both the meter and tester in the event a high current source on the vehicle is left on.

The multimeter is bypassed with the switch during connection in of a surge.

The tester and meter can remain connected until other systems shut down, isolating the drain.

As a convenience, stacking banana connectors are used on the tester.

Automotive Power Drain Leakage Tester Specifications:

12V Car Battery Parasitic Drain Tester Instructions:

1. and turn off the engine, open the hood, lock the door, and wait for the to enter sleep.

2. Clamp the terminal (negative) with the spring clip, then use the fully wrapped clip to clamp the terminal clip (negative)/ground.

3. Flip the switch to the ON position (l/closed); Plug the 4mm banana plug (red) into the multimeter A/10/20A jack, and the 4mm banana plug (black) into the multimeter COM jack.Turn the dial of the multimeter to point to the A/10A/20A gear.

4. Loosen the terminal clip nut with wrench, then disconnect the terminal clip from the terminal, which can be separated by cardboard or sheet.

5. Turn the switch to OFF (O/Disconnect) to read the current value by multimeter.

6. If you need to change the of the multimeter, you should turn the switch to ON (l/Closed), and then turn the multimeter dial. Select the appropriate and re-plug to 4mm banana jack (red) [if necessary], and then turn the switch to OFF (ON/Disconnect).

Car Battery Drain Tester Parasitic Current Detector Notes:

1. Please turn off the engine and remove the before testing the current leakage. Do not the engine during the test to burning the fuse.

2. Current leakage testing needs to simulate the usual state when the car is -off, please be sure to shut the door, pull out the (can be locked), so that the car into a sleep state.

3. Different car computers enter the hibernation state at different times, so please be patient when measuring to determine whether current leakage is generated.

4. The standby current varies from car to car, but the value should be between 20 and 60 .

5. It is recommended to use a 10A fuse to replace the fuse of the line tester to burning the multimeter.

CheShiTech.com— China OBD2 Tool, Automotive Diagnostic Tools, Car Key Programmer, OBD2 ECU chip tuning tool Center.

Contact information:

Website: https://www.cheshitech.com
Email: chinaobd2store@gmail.com
Whatapp/Wechat: +86-19870637508/+86-13691674080
https://api.whatsapp.com/send?phone=8619870637508
https://api.whatsapp.com/send?phone=8613691674080